Home › Guides › Pre-Purchase Survey Checklist: What Gets Inspected
Buyer's Guide ยท Class 1 Marine Engineers
Pre-Purchase Survey Checklist: What Gets Inspected
A pre-purchase survey is the only independent look you get at a vessel before you own it. This is exactly what we inspect, what falls outside the scope, and how to read the report when it lands.
Transmission, shaft alignment, stern gland and propeller condition
Fuel system: tanks, lines, filters, shutoffs and signs of contamination
Cooling and exhaust: raw water pumps, impellers, heat exchangers, elbows and risers
Electrical: batteries, charging, alternators, wiring, switchboards and shore power
Plumbing and sanitation: pumps, tanks, hoses and seacocks
Steering, autopilot and hydraulic systems
Refrigeration, air conditioning and domestic systems where fitted
Oil sampling is available on request. Laboratory analysis of engine and gearbox oil detects wear metals, coolant ingress, fuel dilution and moisture that a visual inspection cannot reveal.
Rigging, Sails and Safety
On sailing vessels, standing rigging is inspected at deck level as standard: terminals, swages, turnbuckles, chainplates, mast step and compression. A full inspection aloft, or a rigging specialist's report, is a separate service and should be considered on any vessel where the rigging age is unknown.
Safety equipment is checked for presence and condition: lifejackets, fire extinguishers, flares or EPIRB, lifelines and stanchions, bilge pumps and high water alarms. On commercial vessels this extends to the requirements of the relevant maritime rule set.
What a Survey Does Not Cover
Being clear about the limits is part of doing the job honestly:
Closed or inaccessible areas. Behind linings, under tanks, inside sealed compartments. We report what could not be reached.
Engine and gearbox internals. Assessment is by observation and running condition unless dismantling is authorised.
Destructive testing. Opening up structure or removing fittings is not done without the owner's approval.
Electronics performance. Equipment is checked for operation, not calibrated or bench tested.
Fuel tank internals. Visual and system checks only; tank inspection is a separate exercise.
Rigging aloft. Unless specifically commissioned.
A survey that claims to cover everything is a survey you should not trust.
The Sea Trial
Where a sea trial is included, it happens under load, which is where machinery faults show themselves: overheating at cruise, vibration, gearbox noise, steering load, and how the vessel behaves in a seaway. We attend where possible, or review the results if the trial is run separately.
A sea trial is not a substitute for the static inspection, and the static inspection is not a substitute for a sea trial. They answer different questions.
How to Read the Report
Our reports grade each item so you can see what matters without reading every line:
Grade
Meaning
What to do
G
Good
Serviceable and in acceptable condition.
S
Satisfactory
Serviceable with normal wear for age. Monitor.
R
Requires attention
A defect that should be rectified, with urgency noted.
N/A
Not applicable or not inspected
Outside scope or inaccessible. Stated openly.
Recommendations are prioritised by urgency, and where a defect has a cost implication we say so. That is the document you use to negotiate, to budget, or to walk away.
Red Flags That Should Stop a Deal
Most defects are negotiable. These are the ones that warrant serious caution: structural cracking or delamination in high-load areas, extensive wet core across decks, hull moisture that would require a full peel, engine condition inconsistent with the hours or service history, rigging of unknown age on a vessel you plan to take offshore, and documentation problems such as a missing HIN, unclear ownership or an unresolved insurance write-off history.
None of these are automatically fatal. All of them change the price, or the risk, or both.
Buying a boat? Book the survey before you commit.
Tell us the vessel and the location and we will confirm availability and a fixed price the same day.
Hull and underwater sections, decks and structure, machinery and systems, rigging at deck level, safety equipment and documentation, with moisture readings and a photographic report graded by severity.
How long does a pre-purchase survey take?
Three to six hours for a 7 to 12 metre vessel, a full day for 12 to 18 metres, and up to a day and a half for larger yachts and catamarans. The written report follows within 48 hours.
Should the boat be hauled out for a pre-purchase survey?
Yes. The underwater hull, keel, rudder, running gear and anodes can only be assessed properly out of the water, and those are the areas with the highest repair costs.
Do you survey the engine?
Yes, by observation and running condition: cold start, smoke, temperatures, mounts, leaks and service history. Oil sampling and laboratory analysis is available as an extra, and dismantling is only done if authorised.
Can I attend the survey?
Yes, and we encourage it. Being present lets you see the defects for yourself and ask questions as they come up. It is often the most useful few hours of the whole purchase.