Machinery is where the money goes on most boats, and where a survey by a qualified engineer earns its keep. Wedding & Paine Marine are Class 1 Commercial Marine Engineers: we assess engines and systems the way they are assessed in commercial service, not by ear and not by hour meter alone.
A hull survey tells you what the boat looks like. A machinery survey tells you what it will cost to keep running. Engine hours are the least reliable number on a boat: an engine can have low hours and be ruined by lack of use, or high hours and be in excellent condition because it was serviced properly and worked regularly.
Our assessment is built on evidence: cold start behaviour, oil and coolant condition, exhaust condition, operating temperatures and pressures under load, vibration and alignment, service history against hours, and where appropriate laboratory oil analysis. That is the difference between an opinion and a finding.
Engines are inspected cold before start, then started and brought to operating temperature. We check cold start behaviour and cranking, idle quality, smoke colour and quantity at idle and under load, oil condition and contamination, coolant condition and system pressure, fuel system condition including filters, lines, lift pumps and injectors where accessible, cooling system including raw water pumps, impellers, heat exchangers and hoses, exhaust manifolds, elbows and risers, engine mounts and alignment, and the presence of leaks, corrosion and evidence of overheating.
We compare the recorded hours against the service history, the general condition of the machinery space and the wear evidence we can see. Where the history is missing or inconsistent, we say so, because that is itself a finding.
Gearboxes and clutches, shaft couplings, shafts and bearings, stern glands and dripless seals, cutless bearings, propellers including condition, pitch and damage, rudders and rudder bearings, sail drives and outboard legs. Misalignment and worn mounts are common and are often the real cause of vibration attributed to the engine.
Fuel tanks, fillers, vents, lines, isolation valves, filters and water separators; evidence of contamination, water or microbial growth; exhaust systems including mixing elbows, risers, silencers and skin fittings, which corrode from the inside and fail without warning; raw water intakes, strainers, seacocks and impellers; and cooling system condition including heat exchanger tube stacks where accessible.
A machinery survey without a sea trial is half a survey. We run the vessel under load and record engine temperatures and pressures at cruise and at full throttle, maximum achievable RPM against the engine's rated RPM, speed, fuel burn where instrumentation allows, vibration and noise, shaft and steering behaviour, gearbox operation, and any smoke or exhaust anomalies that only appear under load.
We compare achieved RPM against the propeller's loading. An engine that cannot reach its rated RPM is over-propped or underpowered, and that shows up as a lifetime of overload, which shortens engine life.
Oil analysis is the closest thing to a blood test for an engine. A sample drawn correctly and analysed by a laboratory shows wear metals (iron, chromium, aluminium, copper, lead, tin), coolant contamination, fuel dilution, water, soot, viscosity change and additive depletion. It reveals bearing wear, piston and ring wear, coolant leaks and injector problems before they become failures, and it gives you a baseline for future sampling.
We take samples during the survey, dispatch them to the laboratory, and interpret the results in plain language. Transmission and genset oils can be sampled at the same time. Results typically return within a few working days, and we report them alongside the survey findings.
Gensets, bow and stern thrusters, watermakers, hydraulic systems, air conditioning and refrigeration plant, and battery and charging systems are all assessed where fitted. These systems fail more often than main engines and are frequently overlooked in general surveys.
A machinery survey is priced as a survey day at $1,200 plus GST, with larger or twin-engine commercial installations quoted on scope. Oil analysis is charged at laboratory cost plus handling and is quoted with the survey. Travel is quoted separately outside the Auckland region.
If you are buying, we recommend combining the machinery survey with a full pre-purchase survey so the hull, systems and machinery are assessed together and reported in one document.
Tell us the engines, the hours and what concerns you, and we will scope the survey and quote it. Same-day response.
Straight answers from our Class 1 engineers:
Every survey is carried out by a Class 1 Commercial Marine Engineer:
Wedding & Paine Marine survey vessels across all of New Zealand:
Also surveying in
Auckland · Whangarei · Tauranga · Christchurch · Nelson · Queenstown